图片
2015年12月31日星期四
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Development and use of innovative 2D Stirrup Machi...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Development and use of innovative 2D Stirrup Machi...: 2D Stirrup Machine is called a stirrup stirrups bending machine, also known as rebar bending hoop machine, and we called bending hoop machi...
Development and use of innovative 2D Stirrup Machine
2D Stirrup Machine is called a stirrup stirrups bending machine, also known as rebar bending hoop machine, and we called bending hoop machine, in fact, it is the place of the hand wrench, machine chassis and steel case , used poorly, not as good as it comes by hand, so the staff must learn to bend steel hoop machine. Single pedal bending hoop machine is in use, there is considerable risk of workers' fingers will fix flat folder, it is indeed scary and fear, it is not a laughing matter, the operation to be careful hundredfold . However, the deduction applies to Viagra and two semicircular rib reinforcement hooks single pedal, it has its advantages, but also can not underestimate, in Granville special angle, can be considered a very good cause.
Double springboard is different than single pedal a big step forward, but more than a single pedal is still a great potential to be tapped, can further innovation. Then there are the twin posts of 2D Stirrup Machine, whose main characteristic is continuous, working drawback is that while the two curved angle (90 degrees and 135 degrees), we should get another piece operating table, the effect is not very satisfactory. We use hand-bent stirrups, the workpiece can be moved to the left, we called "Zola molding" can also move the workpiece to the right, we called the "right to pull molding", the use of reinforced bending hoop machine, it was also Similarly, you can also move to the left to the right, left, right, each has its advantages and disadvantages, the workpiece to the left security, human effort, the work to the right person's arm to go along with the machine, but people who suffer tired fast and rapid, regardless of the left to the right, the left and right sides are required bending hoop machine are nailed planks to make it longer, in order to discharge length dash.
The use of 2D Stirrup Machine preferably while there are two, one for bending a small diameter, a curved ribs for a deduction for the bend stirrups, a bend of the hook to the head of a large diameter bend Bend the other end of the hook, when two hook bend, you can put two bending hoop machine placed beneath two channels, so that the machine is just embedded in the channel where the casters, so you can very easily adjust the two steel hoop bending machine distance, and because they maintain stable machine, do not turn the workpiece, which finished first flew Granville Granville other end can be very convenient and neat.
Double springboard is different than single pedal a big step forward, but more than a single pedal is still a great potential to be tapped, can further innovation. Then there are the twin posts of 2D Stirrup Machine, whose main characteristic is continuous, working drawback is that while the two curved angle (90 degrees and 135 degrees), we should get another piece operating table, the effect is not very satisfactory. We use hand-bent stirrups, the workpiece can be moved to the left, we called "Zola molding" can also move the workpiece to the right, we called the "right to pull molding", the use of reinforced bending hoop machine, it was also Similarly, you can also move to the left to the right, left, right, each has its advantages and disadvantages, the workpiece to the left security, human effort, the work to the right person's arm to go along with the machine, but people who suffer tired fast and rapid, regardless of the left to the right, the left and right sides are required bending hoop machine are nailed planks to make it longer, in order to discharge length dash.
The use of 2D Stirrup Machine preferably while there are two, one for bending a small diameter, a curved ribs for a deduction for the bend stirrups, a bend of the hook to the head of a large diameter bend Bend the other end of the hook, when two hook bend, you can put two bending hoop machine placed beneath two channels, so that the machine is just embedded in the channel where the casters, so you can very easily adjust the two steel hoop bending machine distance, and because they maintain stable machine, do not turn the workpiece, which finished first flew Granville Granville other end can be very convenient and neat.
2015年12月29日星期二
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine positioning device supporting c...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine positioning device supporting c...: 2D Stirrup Machine reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the support...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine positioning device supporting c...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine positioning device supporting c...: 2D Stirrup Machine reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the support...
2D Stirrup Machine positioning device supporting characteristics
2D Stirrup Machine reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the support structure of the positioning by the auxiliary support block, positioning the support block and the guide blocks, auxiliary support block in working condition relatively steel bending machine folder handpiece fixed relative to the guide block 2D Stirrup Machine folder handpiece fixed guide block vertically concave guide grooves or guide holes, positioning the support block slidably disposed in the concave guide grooves or guide holes, the lift cylinder located in the positioning support bottom block, the lifting cylinder piston rod acts on the lower end of the positioning of the support block, forcing the positioning of the support block to move upward along the concave guide grooves or guide hole, the upper end of the positioning of the support block is provided with positioning faces were pressed to deal with curved bars positioning. The solution de 2D Stirrup Machine to the existing rebar positioning support device positioned support block as a whole, need to be completely replaced when damaged, and because the role of arm longer need to use the larger cylinder, the higher cost.
2015年12月24日星期四
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine business should ensure workplac...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine business should ensure workplac...: Production assignments 2D Stirrup Machine companies, while important, but safe production of steel bending machine really the most impo...
2D Stirrup Machine business should ensure workplace safety
Production assignments 2D Stirrup Machine companies, while important, but safe production of steel bending machine really the most important, today we look for production safety guidelines steel bending machine business.
1. To strengthen production safety management, responsible for establishing and implementing full safety production responsibility.
2. The strict implementation of national and Corporation on production safety guidelines, laws, regulations, policies and institutions to strengthen safety education and training for workers to receive security training assessment.
3. Production planning and validation of the safety plan, determine the unit of production safety goal. Issuing safety regulations,2D Stirrup Machine safety technical regulations, approved by the major security technology measures to ensure safety in production of capital investment, and constantly improve working conditions.
4. Check and peer assessment and affiliations deputy chief safety production responsibility system implementation.
5. The agency is responsible for sound management of production safety, enrich the technical management full-time security staff. Listen to the safety report, decided to secure the important work incentive.
6. chaired a safety committee meetings, study and solve major problems in production safety.
7. organize the investigation and handling of major incidents, accidents implement the "Three left off" principle, adhere to the Corporation a major accident reporting system.
8. The Ministry of Finance and the head office on safe production guarantee fund management approach, implement payment security guarantee fund, approval Returns Fund.
9. According to the above security responsibilities,2D Stirrup Machine set annually manager (director) annual security plan, implemented in year one by one specific work arrangements.
1. To strengthen production safety management, responsible for establishing and implementing full safety production responsibility.
2. The strict implementation of national and Corporation on production safety guidelines, laws, regulations, policies and institutions to strengthen safety education and training for workers to receive security training assessment.
3. Production planning and validation of the safety plan, determine the unit of production safety goal. Issuing safety regulations,2D Stirrup Machine safety technical regulations, approved by the major security technology measures to ensure safety in production of capital investment, and constantly improve working conditions.
4. Check and peer assessment and affiliations deputy chief safety production responsibility system implementation.
5. The agency is responsible for sound management of production safety, enrich the technical management full-time security staff. Listen to the safety report, decided to secure the important work incentive.
6. chaired a safety committee meetings, study and solve major problems in production safety.
7. organize the investigation and handling of major incidents, accidents implement the "Three left off" principle, adhere to the Corporation a major accident reporting system.
8. The Ministry of Finance and the head office on safe production guarantee fund management approach, implement payment security guarantee fund, approval Returns Fund.
9. According to the above security responsibilities,2D Stirrup Machine set annually manager (director) annual security plan, implemented in year one by one specific work arrangements.
2015年12月22日星期二
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: CNC equipment of 2D Stirrup Machine
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: CNC equipment of 2D Stirrup Machine: 2D Stirrup Machine applications we all know, is relatively wide, but we may CNC device for CNC bending hoop machine do not know how t...
CNC equipment of 2D Stirrup Machine
2D Stirrup Machine applications we all know, is relatively wide, but we may CNC device for CNC bending hoop machine do not know how this works, the next step for you to explain this issue:
NC device is a core part of CNC bending hoop machine, due to the presence of this part of the composition, CNC bending hoop machine has an automatic rapid completion of reinforced straighten, cut to length, bending hoop and cut off function. And has a very high efficiency.
After the NC device 2D Stirrup Machine from the internal memory, remove or accept input device sent to a few paragraphs NC program, through the logic circuit or system software, numerical control device, compiling, computing and logic processing, the output of various control information and instructions to control the work of the various parts of bending hoop machine to carry out the provisions of the orderly movement and action.
In operation the NC device 2D Stirrup Machine must be reinforced in accordance with the requirements of shape and size of the processing, which is in accordance with the trajectory graphics processing, but the track entered only the start and end, which requires us to the path interpolation, that is, In between the start and end coordinates of the trajectory, the data of the densification, obtained a series of intermediate coordinate value, and outputs the data, so as to better complete steel processing.
2015年12月17日星期四
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine equipment running fast
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine equipment running fast: Our company is engaged in mechanical and electrical integration of numerical control equipment research and development and production of...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine equipment running fast
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine equipment running fast: Our company is engaged in mechanical and electrical integration of numerical control equipment research and development and production of...
2D Stirrup Machine equipment running fast
Our company is engaged in mechanical and electrical integration of numerical control equipment research and development and production of the company, I am strong technical force, rich production experience, advanced processing technology and testing methods, advanced product performance, easy to use and reliable. Here to introduce 2D Stirrup Machine features, hoping to be helpful to you.
Bending hoop machine is an extension of deep-bending machines. Better able to be processed into a predetermined angle, model. As 2D Stirrup Machine, with equipment failure rate, bending steel speed, low power consumption without compromising the ribs, low noise, vibration, light; there are efficient and applicable, reliable operation. Double operate, lightweight and flexible, easy to move, accommodate large construction units and steel processing plants stirrups stirrups production; high efficiency, is bent by hand 3-5 times a day can produce 4-6 tons, length accurate for large batch and factory jobs, a wide range of angle adjustment, be adjusted 0-180 degrees, can be bent square, trapezoidal stirrup and U-hook for stirrups processing buildings, bridges, tunnels, and other works of prefabricated.
These are 2D Stirrup Machine features to introduce, I believe we can help, if you want to know more information, go to our website, the company invites customers home and abroad visit, patrons!
2015年12月15日星期二
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine development and use of innovati...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine development and use of innovati...: The machine is called a 2D Stirrup Machine , also known as rebar bending hoop machine, and we called bending hoop machine, in fact, it is ...
2D Stirrup Machine development and use of innovative methods
The machine is called a 2D Stirrup Machine, also known as rebar bending hoop machine, and we called bending hoop machine, in fact, it is the place of the hand wrench, chassis and steel case of the machine, used poorly, not as manual faster it, so the staff must learn to bend steel hoop machine. Single pedal bending hoop machine is in use, there is considerable risk of workers' fingers will fix flat folder, it is indeed scary and fear, it is not a laughing matter, the operation to be careful hundredfold . However, the deduction applies to Viagra and two semicircular rib reinforcement hooks single pedal, it has its advantages, but also can not underestimate, in Granville special angle, can be considered a very good cause.
Double springboard is different than single pedal a big step forward, but more than a single pedal is still a great potential to be tapped, can further innovation. Then there are the twin posts of 2D Stirrup Machine, whose main characteristic is continuous, working drawback is that while the two curved angle (90 degrees and 135 degrees), we should get another piece operating table, the effect is not very satisfactory. We use hand-bent stirrups, the workpiece can be moved to the left, we called "Zola molding" can also move the workpiece to the right, we called the "right to pull molding", the use of reinforced bending hoop machine, it was also Similarly, you can also move to the left to the right, left, right, each has its advantages and disadvantages, the workpiece to the left security, human effort, the work to the right person's arm to go along with the machine, but people who suffer tired fast and rapid, regardless of the left to the right, the left and right sides are required bending hoop machine are nailed planks to make it longer, in order to discharge length dash.
The use of 2D Stirrup Machine preferably while there are two, one for bending a small diameter, a curved ribs for a deduction for the bend stirrups, a bend of the hook to the head of a large diameter bend Bend the other end of the hook, when two hook bend, you can put two bending hoop machine placed beneath two channels, so that the machine is just embedded in the channel where the casters, so you can very easily adjust the two steel hoop bending machine distance, and because they maintain stable machine, do not turn the workpiece, which finished first flew Granville Granville other end can be very convenient and neat.
2015年12月12日星期六
The control section 2D Stirrup Machine's detailed description
Use 2D Stirrup Machine, not only reduces manpower, but also greatly improve the engineering efficiency. As an improvement construction steel bending machine, the following control section as we popularize steel hoop bending machine to enrich your small knowledge base.
El control section 2D Stirrup Machine uses two servo system, a set of bars to control the alignment and feeding, another group turned to control movement. Servo system servo drives, which use industrial control machine, the servo drive control. Using C programming language, etc., according to the digital-analog conversion relationship servo drives perform programming, control key part is how to achieve the reinforced feed displacement and reinforced bending angle control.
Stirrup machine control system, complete control two aspects, first control the reinforced feed length to reach the processing requirements, this part of the displacement of the information through the rotary encoder feedback closed loop control is completed by a group; Secondly, turned processing angle control, a reverse process design point is reached, it is difficult, so the angle sensor information transmitted by the angle, the use of another set of closed-loop control system, the completion of the angle control.
El control section 2D Stirrup Machine uses two servo system, a set of bars to control the alignment and feeding, another group turned to control movement. Servo system servo drives, which use industrial control machine, the servo drive control. Using C programming language, etc., according to the digital-analog conversion relationship servo drives perform programming, control key part is how to achieve the reinforced feed displacement and reinforced bending angle control.
Stirrup machine control system, complete control two aspects, first control the reinforced feed length to reach the processing requirements, this part of the displacement of the information through the rotary encoder feedback closed loop control is completed by a group; Secondly, turned processing angle control, a reverse process design point is reached, it is difficult, so the angle sensor information transmitted by the angle, the use of another set of closed-loop control system, the completion of the angle control.
2015年12月11日星期五
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Stirrup machines should be cleaned
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Stirrup machines should be cleaned: First, wash and clean-up. As a steel processing equipment, Stirrup machines using undoubtedly will leave some residual steel scrap, so af...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: World Quest internal 2D Stirrup Machine
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: World Quest internal 2D Stirrup Machine: Briefly, 2D Stirrup Machine is mainly composed of internal motor, the processing section, and a body, and there are some circuit such as g...
2015年12月10日星期四
World Quest internal 2D Stirrup Machine
Briefly, 2D Stirrup Machine is mainly composed of internal motor, the processing section, and a body, and there are some circuit such as gear and other ancillary equipment. It is worth mentioning that the working part of the machine, the machine has a similar large central disk like device, which is used in the body of curved steel bearing. When the machine is turned on when it will have the support pin stable good reinforcement, while taking advantage of a certain speed will be slow deformation of steel. Therefore, when using the machine only needs to operate the machine, while his hands need help steady reinforcement.
Followed by steel motor, compared to the general equipment,2D Stirrup Machine uses a new type of motor design, not only be safeguarded in power, but also can be very good given the power to make good use reasonable allocation. Electrical equipment capable of multi-level times the speed, to ensure the smooth progress of the construction. 2D Stirrup Machine motor one of the highlights that can be implemented in different directions to achieve speed steel bending intended to achieve.
Followed by steel motor, compared to the general equipment,2D Stirrup Machine uses a new type of motor design, not only be safeguarded in power, but also can be very good given the power to make good use reasonable allocation. Electrical equipment capable of multi-level times the speed, to ensure the smooth progress of the construction. 2D Stirrup Machine motor one of the highlights that can be implemented in different directions to achieve speed steel bending intended to achieve.
2015年12月8日星期二
2D Stirrup Machine storage Precautions
2D Stirrup Machine in storage should pay attention to some things, before long-term storage, or the need for a series of preparatory work, have some benefits of this machine are stored and used again in the future when.
First it must be examined whether the machine itself intact, with damage to check whether the various components, as well as recommended before the steel hoop bending machine storage, the machine itself should be cleaned, since this time again, enabling the machine itself has a in good condition, the effects may be caused by reduction of production work to a minimum. In addition, recommendations are stored in a dry place indoors, because if the conditions to be outdoors, I suggest looking for a flat on the ground and take cover as it blocked.
When storing 2D Stirrup Machine, strict inspection machine switches is closed, fuel control lever should be placed in the idle unknown, each lever has to be placed in the neutral position, and the machine's battery cooling water inside the engine should be removed and the engine and the battery should be cleaned regularly, launch or charging. Finally it, remember also to carry out regular anti-corrosion work, who do not want to see their own money to buy the machine put some time after it becomes unrecognizable, dilapidated it is recommended to store up painting in money, not made up painting a re-paint it.
Maintain good habits do, do protection work before storage, in order to make 2D Stirrup Machine holding state, ready to enter production.
2015年12月3日星期四
Stirrup machines should be cleaned
First, wash and clean-up. As a steel processing equipment, Stirrup machines using undoubtedly will leave some residual steel scrap, so after using the need to develop a good habit, it is timely for the various machines are devices to clean up. So as not to be disturbed in the future use of the process. At the same time when the device is not used to carry out the necessary cleanup is particularly important, including the use of necessary damp cloth with neutral detergent to clean the surface of the device, remove stains and dirt on top of the machine, to avoid the prolonged impact of the machine appearance and performance. In the clean-up time, especially for the interior of Stirrup machines and a number of blind spots clean.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check 2D Stirrup Machine is a regular process that requires a dedicated time to maintenance.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check 2D Stirrup Machine is a regular process that requires a dedicated time to maintenance.
2015年12月1日星期二
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine maintenance skills
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine maintenance skills: First: For large 2D Stirrup Machine , in the time of placement must be absolutely smooth, be sure to keep a straight line reinforcement and...
2D Stirrup Machine maintenance skills
First: For large 2D Stirrup Machine, in the time of placement must be absolutely smooth, be sure to keep a straight line reinforcement and bending machine sincerity levels at work, because if not on the same horizontal line, then, is prone steel bending machine hard uneven, so not only damage to steel, but also for the machine and is also an invisible injury.
Second: Before using the machine, be sure to lubricant to the appropriate place, this is absolutely necessary, because 2D Stirrup Machine itself is by his mighty power, to achieve the steel bending, so for a lot of parts It has a certain degree of damage, and the lubricating oil can help to minimize the damage.
Third: Before starting work, should be fine bending accuracy according to the degree of bending rebar. Although it looks for steel bending machine does not seem to have much damage, but from the point of view that have to take good care can still play a role.
Finally: After we have finished each use to develop a habit of checking. To see whether there is a loose screw, if some parts do look at the timing of the replacement, for the replaced parts must be good statistics, in order to avoid for themselves 2D Stirrup Machine has a more familiar cognition. In this proposal we had better each time and issue inspection record, which would also help to remind ourselves steel bending machine which appear in most aspects, then you can do so at the time focused factory maintenance service.
Second: Before using the machine, be sure to lubricant to the appropriate place, this is absolutely necessary, because 2D Stirrup Machine itself is by his mighty power, to achieve the steel bending, so for a lot of parts It has a certain degree of damage, and the lubricating oil can help to minimize the damage.
Third: Before starting work, should be fine bending accuracy according to the degree of bending rebar. Although it looks for steel bending machine does not seem to have much damage, but from the point of view that have to take good care can still play a role.
Finally: After we have finished each use to develop a habit of checking. To see whether there is a loose screw, if some parts do look at the timing of the replacement, for the replaced parts must be good statistics, in order to avoid for themselves 2D Stirrup Machine has a more familiar cognition. In this proposal we had better each time and issue inspection record, which would also help to remind ourselves steel bending machine which appear in most aspects, then you can do so at the time focused factory maintenance service.
2015年11月26日星期四
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine in the building processing and ...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine in the building processing and ...: We first look, the current development status of 2D Stirrup Machine . Any building construction technology, are divided into three parts,...
2D Stirrup Machine in the building processing and distribution aspects of the development trend
We first look, the current development status of 2D Stirrup Machine. Any building construction technology, are divided into three parts, one concrete mixing; the second is added to the right size steel; three is laying the template. With respect to the concrete mixing and laying formwork, steel processing and production level is relatively backward. Often this happens because of late cutting steel, which led to the construction schedule delays on construction sites. And now the use of a professional cutting machine, there is a professional engaged in steel distribution company specializing in the commercialization of such buildings is now the bottleneck was completely broken.
Secondly, we look at the emerging use of 2D Stirrup Machine business, at the time of the development of steel distribution business, you should pay attention to avoid the following risks. First, we must consider the use of the traditional manual steel cutting process, the efficiency is relatively low, and add automatic steel cutting machine, although the efficiency is greatly improved, but requires some investment. It is proposed according to the volume of business, purchase the appropriate automatic cutting machine equipment, rather than blind investment; the second is the best choice to buy domestic brands cutting machine, cutting machine on the one hand domestic brands, more suitable for domestic conditions, on the other hand the purchase of equipment Money spent is relatively small.
Finally, we look at the domestic steel cutting machine in the building processing and distribution aspects of development. First, in order to ensure that have sufficient traffic, you can consider real estate developer by a certain percentage shareholding to do business; the second is to ensure the use of the utilization of cutting machine can be considered simultaneously for multiple construction sites, distribution of the same model, unified specifications The 2D Stirrup Machine; third is to have basic cold-drawn or cold-drawn process. So you want to buy steel raw materials, as long as the purchase of common uniform size diameter of steel, according to customer needs, the use of cold-drawn or cold-drawn process, to meet customer needs rebar diameter on it.
2015年11月19日星期四
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Installation Precautions 2D Stirrup Machine
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Installation Precautions 2D Stirrup Machine: 2D Stirrup Machine used to bend steel of various diameters and round, fast and efficient: set several holes on the working disk, it can...
Installation Precautions 2D Stirrup Machine
2D Stirrup Machine used to bend steel of various diameters and round, fast and efficient: set several holes on the working disk, it can bend rebar various models of diameter.
1, note, is strictly prohibited within the operating radius of curved steel and body to stand; In addition, semi-finished products to be stacked neatly curved good, can not hook up.
2, steel bending arc machine wheel change direction, then it must be very stable.
3, after the job is completed, to promptly clean up the site, maintenance of good mechanical, power lock box.
4, regular inspection of the mandrel, the stopper, turntable, to ensure that there will be no damage and crack phenomenon, in addition to securing a reliable shield to empty the machine after the operation confirmed before normal operation.
5, 2D Stirrup Machine, non-mechanical processing exceeds the specified rebar diameter, root number and mechanical speed.
6, reinforced bending arc machine periodically check the mechanical performance is good, countertops table and bending machines to maintain the level; and various ready ahead of the mandrel tool block.
7, in accordance with the diameter and 2D Stirrup Machine, steel processing requirements to install the mandrel, forming the shaft, gear shaft or variable iron fences, and 2.5 times the diameter of the mandrel bar diameter.
8, when the job may need to bend the bars inserted in one end of the dial fixed gap, the other end is fixed and hand pressed against the body; check fuselage fixed, mounted on one side of the block to ensure that before the start of steel.
2015年11月13日星期五
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine mechanism works
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: 2D Stirrup Machine mechanism works: CNC 2D Stirrup Machine mechanism works: cut off in the middle of the center of the piston is provided with a spool and spring, a...
2D Stirrup Machine mechanism works
CNC 2D Stirrup Machine mechanism works: cut off in the middle of the center of the piston is provided with a spool and spring, at idle, due to the action of the spring, leaving the middle of the center pillar river hole cylinder, high-pressure oil from this hole through the eccentric shaft oil passage back into the tank. When 2D Stirrup Machine cut, in order to push the piston manpower, 'the central spool blocked the center hole cylinder, this time coming from the high-pressure piston pump oil through the inlet valve into the cylinder, resulting in high pressure pushes the piston movement, the piston driven cutter for cutting steel. When the pressure of the spring effect is greater than the thrust reverser inner cylinder pressure, the spool will return to the original position, oil flows back into the tank along the central hole of the oil. Cut off the return of the piston, relying on the plate spring return force to achieve.
2015年11月10日星期二
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Buy 2D Stirrup Machine need to know three importan...
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Buy 2D Stirrup Machine need to know three importan...: First, choose well-known, large-scale manufacturers. Manufacturers need to carefully choose, now often promote how their manufacturers how ...
2015年11月9日星期一
Buy 2D Stirrup Machine need to know three important details
First, choose well-known, large-scale manufacturers. Manufacturers need to carefully choose, now often promote how their manufacturers how well the network, but this is only one-sided on the network, Stirrup machineto really buy it, or should personally lead manufacturers to take a look, understand the manufacturer's production capacity, environment , as well as the level of quality of service and staff personnel, summary judgment by the manufacturers of these indirect authenticity.
Second, remember not to forget the service. Many customers after the purchase of equipment, there is always a problem in the device will be remembered after sales service, but this time to think of it is probably too late. Such large-scale equipment2D Stirrup Machine, be sure to consult the manufacturer service and things that inevitably occur in the use of small problems, if they have these little problems, I am afraid will be very troublesome. But if you have a service that you can reduce a lot of trouble, they will help you solve the problem.
Third, check the quality of the equipment on the spot. Steel bending machine needs to check the quality of the spot, it is best to let the staff help operate it, in the course of device operation, if a problem is found, must be promptly replaced or returned. The most important thing is to check the various parts of the device parts, to see which parts manufacturer out. If the device is damaged after a part, it is best to replace the same parts manufacturers to ensure the normal operation of the device.
Over to you about the three basic things about buying 2D Stirrup Machine needs attention. Steel bending machine such large equipment cost a lot of money, any one industry will not easily funded, certainly in many aspects of the investigation after the final determination of an ideal device, in particular, should choose the time and attention to detail issues.
2015年11月6日星期五
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Caution 2D Stirrup machine
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines: Caution 2D Stirrup machine: First, check Stirrup machine mechanical performance is good, the table and the table to maintain the level bending machine; and ready for ...
2015年11月5日星期四
Caution 2D Stirrup machine
First, check Stirrup machine mechanical performance is good, the table and the table to maintain the level bending machine; and ready for all kinds of mandrel tool block.
Second, according to the diameter and bending hoop machines installed rebar processing requirements mandrel forming axis, iron shaft gear or a variable fences, mandrel diameter should be 2.5 times the bar diameter.
Third, check the mandrel, the stopper, the turntable should be no damage and cracks, securing reliable shield, confirm normal machine operation by air before the operation.
Fourth, when the job will need to bend rebar inserted in one end of the fixed turntable with a gap, and the other end is fixed and hand pressed against the body, inspection body fixed, and indeed on the side of safety before starting block reinforcement.
Five non-replacement of jobs and change the angle of the mandrel and the governor and other operations, nor refueling or removal.
Sixth, bending steel, non-processed 2D Stirrup Machine CNC machines for the specified rebar diameter, root number and mechanical speed.
Seven high bending stiffness or low alloy steel, machinery nameplate should be a maximum limit for standard diameter, and replace the corresponding spindle.
Eight, prohibited within the operating radius of curved steel and the body does not have a fixed side stop people. Curved good semi-finished products should be stacked neatly, hooks shall not be upward.
Nine, turntable commutation, must be carried out after it stops.
Ten, the job is finished, clean up the site, maintenance2D Stirrup Machine, power lockbox
Second, according to the diameter and bending hoop machines installed rebar processing requirements mandrel forming axis, iron shaft gear or a variable fences, mandrel diameter should be 2.5 times the bar diameter.
Third, check the mandrel, the stopper, the turntable should be no damage and cracks, securing reliable shield, confirm normal machine operation by air before the operation.
Fourth, when the job will need to bend rebar inserted in one end of the fixed turntable with a gap, and the other end is fixed and hand pressed against the body, inspection body fixed, and indeed on the side of safety before starting block reinforcement.
Five non-replacement of jobs and change the angle of the mandrel and the governor and other operations, nor refueling or removal.
Sixth, bending steel, non-processed 2D Stirrup Machine CNC machines for the specified rebar diameter, root number and mechanical speed.
Seven high bending stiffness or low alloy steel, machinery nameplate should be a maximum limit for standard diameter, and replace the corresponding spindle.
Eight, prohibited within the operating radius of curved steel and the body does not have a fixed side stop people. Curved good semi-finished products should be stacked neatly, hooks shall not be upward.
Nine, turntable commutation, must be carried out after it stops.
Ten, the job is finished, clean up the site, maintenance2D Stirrup Machine, power lockbox
2015年6月17日星期三
2015年5月29日星期五
2015年5月24日星期日
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines
Small stirrup machine
Introduction:
Steel bar stirrup bender is designed to bend steel bar by 90°and 135°. It can bend 4, 18 and 20mm round bar into various needed geometrical shape. CNC Rebar stirrup bending machine is with simple process, high efficiency, easy adjustment and even bending.
Features:
1. It has 90°and 135°foot switches, which ensures easy adjustment.
2.Steel bar stirrup bender is easy to operate, even no need of training.
3.Range of angle is between 0°and 360°.
4. It has high rotate speed, 20-25 times per second, and 500 stirrups per hour.
Operation requirements and notice:
1.Check whether there is loosed screw or damage before installation.
2.CNC Rebar stirrup bending machine must be equipped with earth leakage circuit breaker and connects grounding wire.
3.Adjust degree of parallelism and interval between striker plate and bending accessories in accordance with dimension of bended rebar.
4.Fix the screw of angle clamp when reaching the needed angle.
Specification:
Item GW20
capacity Rod Φ4-20mm
Rebar Φ4-16mm
spindle speed 20-25rpm
power 1.5-2.2KW
motor 380V/50HZ/3phase
foot pedal dual foot pedal
angle 90, 135
power supply electricity
control mode automatic
Application carbon steel, hot/cold rolled steel
weight 130kg
dimension 1300×550×720
Pre-sales service:
1. Foreign customers are welcome to visit our factory for free.
2.Customize special steel bar stirrup bender as per customers’ demands for free.
3.Provide manual in Chinese, English, Spanish, Portuguese, French, Arabic, Russian and Thai for special products.
In-sales service:
1. Provide technical support for customers on machine operation to ensure they can operate correctly.
2.Supply wearing parts for free and we are responsible for inland freight cost.
3.Delivery time of domestic orders: 1to 3 days.
4.Delivery time of overseas orders: 5 to 15 days.
After-sales service:
1.24 hours after-sales technical support for free.
2.Provide one year quality warranty for CNC Rebar stirrup bending machine.
3.Replace damaged parts of quality problem within the quality warranty period.
Introduction:
Steel bar stirrup bender is designed to bend steel bar by 90°and 135°. It can bend 4, 18 and 20mm round bar into various needed geometrical shape. CNC Rebar stirrup bending machine is with simple process, high efficiency, easy adjustment and even bending.
Features:
1. It has 90°and 135°foot switches, which ensures easy adjustment.
2.Steel bar stirrup bender is easy to operate, even no need of training.
3.Range of angle is between 0°and 360°.
4. It has high rotate speed, 20-25 times per second, and 500 stirrups per hour.
Operation requirements and notice:
1.Check whether there is loosed screw or damage before installation.
2.CNC Rebar stirrup bending machine must be equipped with earth leakage circuit breaker and connects grounding wire.
3.Adjust degree of parallelism and interval between striker plate and bending accessories in accordance with dimension of bended rebar.
4.Fix the screw of angle clamp when reaching the needed angle.
Specification:
Item GW20
capacity Rod Φ4-20mm
Rebar Φ4-16mm
spindle speed 20-25rpm
power 1.5-2.2KW
motor 380V/50HZ/3phase
foot pedal dual foot pedal
angle 90, 135
power supply electricity
control mode automatic
Application carbon steel, hot/cold rolled steel
weight 130kg
dimension 1300×550×720
Pre-sales service:
1. Foreign customers are welcome to visit our factory for free.
2.Customize special steel bar stirrup bender as per customers’ demands for free.
3.Provide manual in Chinese, English, Spanish, Portuguese, French, Arabic, Russian and Thai for special products.
In-sales service:
1. Provide technical support for customers on machine operation to ensure they can operate correctly.
2.Supply wearing parts for free and we are responsible for inland freight cost.
3.Delivery time of domestic orders: 1to 3 days.
4.Delivery time of overseas orders: 5 to 15 days.
After-sales service:
1.24 hours after-sales technical support for free.
2.Provide one year quality warranty for CNC Rebar stirrup bending machine.
3.Replace damaged parts of quality problem within the quality warranty period.
2015年5月20日星期三
2D Stirrup Machine,Stirrup machine,Stirrup machines，Small Stirrup Machine，Small stirrup machines
2D stirrup bending machine, controlled by CNC, is adopted to measure, straighten, bend and cut hot rolled rebar, hot rolled ribbed steel bar, plain round bar and cold rolled rebar quickly and automatically. As a recognized CNC bending and cutting machine supplier, our product is composed of traction part, straightening part, shearing part, bending part and electric control part. As a renowned factory in China, our 2D rebar stirrup machine is with high performance and competitive price, and wins customers’ trust and praise.
1.2D stirrup bending machine has stable work performance and competitive price.
2. Combining straightening, bending and cutting in one, which ensures various shapes in accordance with your requirements.
3.Two-way hydraulic line is changed into one-way, which is simpler and with less tolerance.
4.CNC stirrup bender has high feeding speed and cutting efficiency.
5.It can bend two rebar one time, with high performance and easy adjustment.
1. Avoid damage caused by rain, sunshine, sand and dust.
2. Check the traction part and oil tanks to refuel or change lubricant.
3. Clean the CNC bending and cutting machine before and after operation. Take away the oxidized steel and sundries.
4. Check the tightness of blades and bending part, as well as whether the blades and initial point are reset or not.
5. Monthly maintenance. Check whether there is oil leakage or screw loose in the mechanic part, the oil level in hydraulic oil tank and the tightness of circuit connection.
6. Lubricate the traction wheels every 3 month.
7. Keep pressure between 8Mpa to 10Mpa.
8. For long term stock, cut off power supply before maintenance. Set all section in out-of-service state. Paint anti-rust oil on places easy to rust. Cover 2D stirrup bending machine with waterproof bag. Put the key in a safe place.
1.2D stirrup bending machine has stable work performance and competitive price.
2. Combining straightening, bending and cutting in one, which ensures various shapes in accordance with your requirements.
3.Two-way hydraulic line is changed into one-way, which is simpler and with less tolerance.
4.CNC stirrup bender has high feeding speed and cutting efficiency.
5.It can bend two rebar one time, with high performance and easy adjustment.
1. Avoid damage caused by rain, sunshine, sand and dust.
2. Check the traction part and oil tanks to refuel or change lubricant.
3. Clean the CNC bending and cutting machine before and after operation. Take away the oxidized steel and sundries.
4. Check the tightness of blades and bending part, as well as whether the blades and initial point are reset or not.
5. Monthly maintenance. Check whether there is oil leakage or screw loose in the mechanic part, the oil level in hydraulic oil tank and the tightness of circuit connection.
6. Lubricate the traction wheels every 3 month.
7. Keep pressure between 8Mpa to 10Mpa.
8. For long term stock, cut off power supply before maintenance. Set all section in out-of-service state. Paint anti-rust oil on places easy to rust. Cover 2D stirrup bending machine with waterproof bag. Put the key in a safe place.
2015年5月19日星期二
2015年5月18日星期一
2015年5月15日星期五
2015年5月14日星期四
2015年5月13日星期三
2015年4月12日星期日
2015年1月27日星期二
2D practical stirrup machine?
2D stirrup machine using CNC bending hoop machine will greatly improve labor productivity, the corresponding area, labor costs, energy consumption will be significantly reduced. 2D stirrup machine at the same time due to the use of high affinity human-computer numerical control technology, small stirrup machine makes the operator's labor intensity greatly reduced.
The practical application of 2D stirrup machine?
2D stirrup machine current domestic steel processing method is still lagging behind in highway construction, 2D stirrup machine equipment and tools generally obsolete, stirrup machine mainly dominated manually, 2D stirrup machine automation level is not high, production efficiency low, time-consuming, the poor quality parts, and labor-intensive, high cost.
订阅：
博文 (Atom)